• 

• 3G 7dBm PICO Home Booster Specification

  Model No. PHB-1800

Specifications

Parameters		Specifications
Frequency Range	Up Link (RX)	1710 ~ 1725 MHz
	Down Link (TX)	1805 ~ 1820 MHz
Frequency Bandwidth		15 MHz
Gain		≧ 60 dB(in-band > 60dB)
Gain Flatness		≦ ± 1.5 dB
		(Peak to Peak ≦ -0dB ~ +3dB)
Automatic Gain Control Range (AGC)		≧ 20 dB
Auto Gain Setting		15dB @ 1dB/ Step (Gain : 45~60dB)
Maximum Input Power (Without Damage)		0 dBm (with AGC ON and Full Attenuation)
Output Power	Up Link (RX)	≧ 7 dBm / One Carrier (RMS)
		≧ 4 dBm / Two Carriers (RMS)
	Down Link (TX)	≧ 7 dBm(in-band>7dBm) / One Carrier
		≧ 4 dBm / Two Carriers
Automatic Shut Down Power Level (Always Auto Recovery)	Up Link (RX)	O/P ≧ + 9 dBm / One Carrier
	Down Link (TX)	O/P ≧ + 9 dBm / One Carrier
Group Delay		＜ 2.5 us
Noise Figure		＜ 6 dB @Max Gain
VSWR		≦ 1.5:1
TX / RX Isolation		＞ 75 dBc
Frequency Stability		＜ ± 0.01 ppm
Out of Band Gain	0.2≦f_offset＜1.0 MHz	＜ 60 dB
	1.0≦f_offset＜5.0 MHz	＜ 45 dB
	5.0≦f_offset＜10.0 MHz	＜ 45 dB
	10.0 MHz≦f_offset	＜ 35 dB
Operating band Unwanted emission	0.015 MHz ≤ f_offset < 0.215 MHz	< -14 dBm /RBW13KHz
	0.215 MHz≤ f_offset < 1.015 MHz	< -14 dBm /RBW13KHz
	1.015 MHz ≤ f_offset < 1.5 MHz	< -26 dBm /RBW13KHz
	1.5 MHz ≤ f_offset < 10.5 MHz	< -13 dBm /RBW 1MKHz
	10.5 MHz ≤ f_offset < f_offsetmax	< -15 dBm /RBW 1MKHz
Spurious Emission	-36dBm/RBW 1KHz @ 9 KHz ~ 150 KHz	Fully comply With 3GPP TS 36.106 Chapter 9 (Category B )
	-36dBm/RBW 10KHz @ 150 KHz ~ 30 MHz
	-36dBm/RBW 100Khz @ 30 MHz ~ 1 GHz
	-30dBm/RBW 1MHz @ 1 GHz ~ 12.75 GHz
Error Vector Magnitude (EVM)		≤7 % RMS
Adjacent Channel Rejection Ratio (ACRR)		≧ 25dB @± 5 MHz & ±10 MHz
Input Intermodulation		Fully comply With 3GPP 36.106
Output Intermodulation		Fully comply With 3GPP 36.106
Impedance		50Ω
RF Connectors	Single I/P Port	SMA type Female Connector
Environment Condition		IP30
Power Consumption		≦ 8W
Power Plug		Taiwan Type
Power Unit		AC (110~220V, 20%)(Plug type--1 round pin and 2 flat pins, Taiwan type) to DC adapter with International Safety Approval (CE, GS, CSA, UL, 3C, NSDFI, …)
		PSU have current protection. PSU will automatically shutdown when abnormal current is occuring.
		PSU have temperature sensing function. When temp of PSU or repeater body is over limit, PSU will automatically shutdown and send alarm via RCU board.
Operating Temperature		0 ℃ ~ + 55 ℃
Humidity		≦ 95 ％
Cooling		Heat sink Convection Cooling
Dimension (H * W * D)		95*185*35mm
Weight		≦ 1Kg
External Donor Ant Gain		≧ 7dBi
External Donor Ant Dimension		≦ 11.3*9.5*2.3 CM
Embedded Service Ant Gain		Embedded with Gain as Max 2dBi ( 0 ~ 2dBi)
External Service Output Port Loss		3dB
Material Certificate		RoHS
Jumper Cable Loss		10m ＜ 6dB loss
Mean Time Between Failure (MTBF)		≧ 50,000 Hours
Alarm		AGC out of range, Auto Isolation Detection
ISO Detection & Auto Gain Setting		Periodically check the real ISO and Auto Gain Setting(AGS) after ISO check. Auto Daily Isolation check
Auto Shutdown & Auto Gain Setting		System shall auto-shutdown when ISO is not enough. And system can auto-recover by itself until 3 times. Once the lack-isolation status is still there after 3-times-auto-recovery, then system becomes Always-SD until AC RESET
LED Indicators		PSU (1pcs Green LED)
		UL and DL HPA Failure (1pcs Red LED)
		UL and DL Isolation Alarm (1pcs Red LED)
		Isolation / Output Level Display (by Green LED)