• 

• 3G 7dBm Band Selective Repeater Specification

  Model No. PHB-2100

Specifications

Parameters		Specifications
Frequency Range	Up Link (RX)	1945 ~ 1960 MHz
	Down Link (TX)	2135 ~ 2150 MHz
Frequency Bandwidth		15 MHz
Channel Spacing		5 MHz
Operating Band：Number of Channels		3 FA (15MHz)
Gain		≧ 60 dB(in-band > 60dB)
Gain Flatness		≦ ± 1.5 dB
		(Peak to Peak ≦ -0dB ~ +3dB)
Manual Gain Control Range (MGC)		40 ~ 60 dB in 1 dB/step
Automatic Gain Control Range (AGC)		≧ 20 dB
UL/DL Band Rejection		>75dB
Gain Control Accuracy		＜ 0.9 dB
Maximum Output Power	Up Link (RX)	+ 13 dBm / One Carrier (RMS)
		+ 10 dBm / Two Carriers (RMS)
	Down Link (TX)	+ 7 dBm(in-band>7dBm) / One Carrier (RMS)
		+ 4 dBm / Two Carriers (RMS)
Automatic Shut Down Power Level (Always Auto Recovery)	Up Link (RX)	O/P ≧ + 15 dBm / One Carrier (RMS)
	Down Link (TX)	O/P ≧ + 9 dBm / One Carrier (RMS)
Maximum Input Power (Without Damage)		+0 dBm (with AGC ON and Full Attenuation)
Group Delay		＜ 6 us
Noise Figure(Uplink)		＜ 6 dB @Max Gain
VSWR		≦ 1.5:1
TX / RX Isolation		＞ 75 dBc
Frequency Stability		＜ ± 0.01 ppm
Out of Band Gain	2.7≦f_offset＜3.5 MHz	＜ 60 dB
	3.5≦f_offset＜7.5 MHz	＜ 45 dB
	7.5≦f_offset＜12.5 MHz	＜ 45 dB
	12.5 MHz≦f_offset	＜ 35 dB
Spectrum Emission Mask	2.515MHz≦f_offset＜2.715MHz	＜ - 22 dBm / RBW 30 KHz
	2.715MHz≦f_offset＜4.0MHz	＜ - 34 dBm / RBW 30 KHz
	4.0MHz≦f_offset＜8.0MHz	＜ - 21 dBm / RBW 1 MHz
	8.0MHz≦f_offset＜f_offset(max)	＜ - 25 dBm / RBW 1 MHz
Spurious Emission (Category B)	9 KHz ~ 150 KHz	＜ - 36 dBm / RBW 1 KHz
	150 KHz ~ 30 MHz	＜ - 36 dBm / RBW 10 KHz
	30 MHz ~ 1 GHz	＜ - 36 dBm / RBW 100 KHz
	1 GHz ~ 12.75 GHz	＜ - 30 dBm / RBW 1 MHz
Spurious Emission (Category B)	Co-existence and Co-location	Comply With 3GPP TS 25.106
Error Vector Magnitude (EVM)		＜ 10 % RMS (16QAM for HSDPA+ support)
Peak Code Domain Error (PCDE)		＜ - 35 dB (at SF=256)
Adjacent Channel Rejection Ratio (ACRR)	± 5 MHz	＞ 25 dBc
	± 5 MHz & ±10 MHz	＞ 25 dBc
Input Intermodulation		Increase ＜ 10 dB
Input Intermodulation	Co-existence and Co-location	Comply With 3GPP TS 25.106
Output Intermodulation (Downlink only)		Comply With 3GPP TS 25.106
Impedance		50Ω
Serivce Antenna		Built-in
In/Out RF Connectors	Single I/P Port and Single O/P Port	SMA type Female Connector
Environment Condition		IP30
Power Supply		I/P : AC 110V / 220V ± 10 % , 47 ~ 63 Hz (US Plug Type)
		CE Certificate
Power Consumption		≦7.5 W (5V, 1.5A)
Operating Temperature		0 ℃ ~ + 55 ℃
Humidity		≦ 95 ％
Cooling		Heat sink Convection Cooling
Dimension (H * W * D)		160 x 75 x 30 mm
Weight		≦ 1 Kg
Build-In Service Antenna		Needed
External Donor and Service Ant Gain		≧7dBi
External Ant Dimension		≦20*20*6 CM
Mean Time Between Failure (MTBF)		＞50,000 Hours
Material Certificate		RoHS
Jumper Cable Loss		10m＜6dB
RF Character		Comply With 3GPP TS 25.106
EMC		Comply With 3GPP TS 25.113
Safety		Comply With EN 60 950,ETL
Power Unit		AC (110~220V, 20%)(Plug type--1 round pin and 2 flat pins, Taiwan type) to DC adapter with International Safety Approval (CE, GS, CSA, UL, 3C, NSDFI, …)
		PSU should have current protection. PSU will automatically shutdown when abnormal current is occuring
		PSU should have temperature sensing function. When temp of PSU or repeater body is over limit, PSU should automatically shutdown and send alarm via RCU board.

LED Indicators

LED Indicators	On (green) / Off (dark)	PSU
		Automatic Gain Trailing
	Normal (dark) or Alarm (red color)	UL and DL HPA Failure (1pcs LED)
		UL and DL Isolation Alarm (1pcs LED)
		Isolation Auto Detection
	Output Level Display (by 7-Segment)

Accessories

Accessories 1.Home Booster Body Unit * 1pcs 2.AC/DC Adaptor * 1pcs 3.External Patch Antenna(7dBi) * 1pc 4.Jumper RF Cable(10M) * 1pc 5.Mounting Bracket * 1set